On this page we will be posting long awaited pictures of pans, burners and baskets along with a few custom burners we are building for our customers.
The pan burner below is for a 2 sided fireplace and this pan is 25" x 45" and controlled from only one side. It is constructed from 16 gauge brushed stainless steel with 3" x 3" x 3" corner legs.
The picture on the bottom left shows you the thermo-coupler and safety pilot light kit which are UL and CSA approved.
This is one side of the two sided fireplace and we will post pictures when the glass is installed of both sides.
The 6 pictures below are of an antique coal basket using Bronze, Bronze Reflective and Starfire
The 6 pictures above are of an antique coal basket using Bronze, Bronze Reflective and Starfire
The 5 pictures below are renderings of several fireplace burners we were asked to design
The first is a simulation of a pan with glass and a burner like an antique coal basket.
This last one is the same in a smaller version of our pan.
The 5 pictures above are renderings of several fireplace burners we were asked to design
The four pictures below are of a pan in Palm Springs California
This picture is the pan on high with no glass
This is the pan and glass for a full fire effect
The four pictures above are of a pan in Palm Springs California
The 6 pictures below are of a fireplace we converted to a pan from a double burner
this picture is with a double burner
The 2 pictures below is with the pan underneath
This is the pan exposed just under the glass
The 6 pictures above are of a fireplace we converted to a pan from a double burner
The pictures below are of John Hanson in Northern California and he did a pan burner we provided and installed it himself.
A Clear base with 3/4" Clear on top
Here is how it all started
The bottom of the pan goes in
The top goes on and you light it
Now the glass
and now the magic
This is how the pan started
There you have it, simple as that. Great job John Hanson!
The several pictures below are of a modern coal basket of stainless steel with legs or it can be suspended with chains. This will also be one of our new product lines available in several sizes and finishes.
The pictures below give you an idea on what a pan can do for a larger fireplace.
The stainless steel tray below has Azurlite in the tray. A very clean and simple look.
The custom fireplace below has a star burner and a very nice star opening
From the start......
to the finish
Very modern. The fireplace above has Gray, Gray Reflective, Black, and Black Reflective
The fireplace below is in Georgia and we will explain as we move down
The first 2 pictures are of how it used to look, nice logs! I don't think so!
The owners of this fireplace called and told us they couldn't use the fireplace because of the soot (carbon-monoxide) (poison) So we redesigned the fireplace with an air vented pan and our glass (Starfire and Ice) and now a clean burn! The flames are all above the glass and therefore no more carbon-monoxide. Fireplace Shops and dealers won't tell you about this unless you ask, how would you know to ask?
Starfire and Ice on the left
Pan and ring burner on the right.
Really nice fireplace in the middle of the great room surrounded by 3 glass walls.
The fireplace below is a vent less with a steel pan and a stainless face added to cover the controls. The glass is Azurlite with ice ice ice. Ahhhhh the beauty of no logs! Really!
Can you honestly say logs look good?
Below is a 36" aluminum pan burner for propane with a 3" outside lip. These can be made to fit any fire pit, fire table of fire fit for natural gas or propane. We can build anything! This pan has a thermo-coupler for safety and air mixer built in to eliminate soot.
The fireplace below is a propane burner, self installation with the 2" method, Starfire and Gold on top
Above we have the old burner with a smaller flame pattern which we will change to a double burner in our tray propane pan burner
A little bit of cleaning with a wire brush and 1200 degree paint
We filled the bottom with pea gravel and the covered it with sand
Then we installed the propane burner and filler it with pea gravel to the top of the burners
You can see the pilot light and thermo-coupler exposed
So there it is. A clean burning propane burner, 2" method, no soot, no smells, no carbon monoxide and it puts out a tremendous amount of heat. We sell the 2" method because it works and if anyone tries to tell you different, they need your money more than you do. We are the only company building propane burners for glass that don't soot or smell!
These are our round ring burners with out the center hub and these can be made in any size in steel or stainless steel
The pan below is a brushed aluminum pan with sculpted legs. This pan is for propane and now we offer a simple adapter to convert this to remote control from the back side (battery operated). The glass installed is a multi mix for the photo shoot only. The pan is 2" with 3" legs. This pan will be installed in Cabo San Lucas, Mexico
The half round burners below were installed at the Marriott "Gas Lamp" San Diego, California in a 72" Fire pit. We will post pictures of the finished project when we get the pictures sent to us. These were 24" x 48" stainless steel half round burners.
The fire pit below shows our FPPK (fire pit propane kit) a 30" base with a double 24" stainless steel burner. You will notice the igniter and thermo coupler (heat switch for safety). The base plate is to prevent propane from leaking into the fire pit below.
Below, this is what a ventless burner looks like when you purchase one and we can do with it for you.
All of our sheet metal and welding is now done in house as we acquired a full sheet metal facility.
The vent less burner below is 1 of 3 that were sent to Georgia. The glass that we tested was Multi Mix. We show the burner finished, with the burners exposed, burning and with glass, We will post the pictures of the finished fireplace when the customer send them to us to post. This is a propane ventless burner and these also are made in natural gas as well.
Notice the stainless box tray underneath the upper pan.
If you dream it, design it, think of it, we can build it as we are the innovators in the industry which seem to some how give licence for most to try to copy us and our products and designs. What is important that you know who we are!
The vent less burner below is made of steel and there were actually 4 of these made. We covered the front and sides with 5" skirts. There are being installed in Georgia and as soon as they send pictures we will post them These pictures were taken just after the testing. This is a propane vent less burner and these are available in natural gas as well.
The pictures below are of the same burner as above with Azurlite installed. These 4 ventless burners are being installed in Georgia.
The skirts will hide the the valves and the remote control will be moved to the side of the fireplace. This was a ventless burner the customer sent to us for conversion and they asked for us to add a remote to all 4 ventless burners.
The fireplace below is a vent less self install by Norm. The colors used were: Starfire base, Cobalt Blue Topper, Pale Cobalt Blue Topper, Ice Ice Ice, Pale Gray Topper, Gray Topper and Copper Blue Topper.
We use a piece of stainless steel in the front to contain the glass to cover the burners and keep the glass level.
The vent less burner below shows where the sensor has to be and how it works. This is a stainless steel pan with Gold glass for the test burn.
The fire pit below is a 36" round stainless steel pan with a 24" stainless steel ring. The glass is Bronze Rust Copper. This pan can easily be adapted for propane as well.
The flat pan below has a propane burner installed for a fire pit. These are made in any size, shape or burn pattern. The one shown below is an electronic ignition control and these can be adapted with manual ignition as well. This was build for a designer in New York and placed on a shelf of the fireplace.
The pan burner below is a stainless steel/ propane pan for outdoors and we have installed an electronic ignition under the pan. These can also be made for natural gas.
The table below was built for Jim Shaw in Riverside California. The stainless steel tray with stainless steel burners was build to Jim's specs. We used Bronze glass, Bronze Reflective glass and Pink Diamonds.This was a natural gas burner and could be easily converted to propane.
The pictures below are from Iggy in New York. He sent me a picture of his fireplace and asked me what we can do to help him. Well sit down and watch. A new pan, hood, surround, tile and Starfire! Nice insert, not! Just like "Nice Logs", not!
below is a template for the stainless steel pan
Below we added a pan
Below we added a vent which was taken out years ago.
Above you can see the the key valve and below you don't see it. Because we made a removable panel!
There you have it in Rochester New York, Iggy it looks great.
The burner below has a 300,000 btu controller, 36" triple ring mounted on a 48" aluminum base plate for a fire pit in San Diego. These can be adapted for natural gas or propane with up to a 96" lead pilot light and igniter.
The bowls below are a newer product which we can help you convert your table you have now or build a table around the the bowl we provide you. We can build these for natural gas or propane. Filled with crushed lava rock and ready for what ever you would like to cover it with. We can spin bowls in any size. These come with steel or stainless steel rings, double or single rings. The bowl are very economical and are available up to 24". Anything over 24"will be a custom size, but we can make any size.
These bowls were set up for propane and as you can see the thermo coupler in the picture above.
The propane burner below was made to inset flush to the floor with a remote control underneath the pan. The pan sat 5" below the surface so the glass would appear to be just above the surface. The outer ring was bolted down to keep the glass from falling underneath the burner in the event you ever had to service the burner or remote control. The tower you see is actually for the air mixer to draft fresh air to the propane before it burns.
As you can see we drilled it to look like a ribbon burner. This is what was ordered by the customer.
The two pans below are stainless steel and are propane fueled with 415,000 btu electronic ignitions each.
Our products do not require any certification from the AGA, CSA or UL as it is considered a stand-alone product by these agencies. We are told that we would need a certification if sand and or lava rock would need certification. The agencies are franchise operations and they are privately owned and they are not a government agency. These agencies are hired for mass production testing and AGA, CSA and or UL do not certify custom one of a kind projects. Custom burners need no certification as this only applies to production equipment. Just so you can understand that a certification costs about $15,000.00 and certification was developed for production/ mass production to assure quality. Any parts that would normally need AGA or UL do in fact have these approvals. Parts with function need and should have some sort of approval. The pan burners we sell that do have UL, CSA and or any other listings are produced by other companies. The custom pan burners that we produce are just that, custom. Therefore do not require UL, CSA and or any other agency listings as these are custom. The parts that we use to build these pans are UL, CSA listed as they should be. We would never use any “Third World Country” or any unlisted, untested parts to build any products and or parts to endanger any product performance what so ever.
Has anyone ever told you "Nice Logs" ? Nooo, I don't think so.
"Utility Patent Applications now Published as of June 2005 and May 2006"
We are still in Patent Pending
We take pride in our new product and take Patent Infringement very seriously! There are several companies who have copied our product and or process and they will be in for a surprise when our patent number becomes available to the public.
Please take note that in the United States reasonable royalties begin to accrue when a Patent publishes, (as ours has in June of 2005 and in May of 2006) depending on the state of the patent application at the time of issuance. Please take note that we do intend to enforce our patent rights to the furthest extent of the law upon issuance of our patent.
Patent publication available on request. Don't be fooled by look-a-likes or overly expensive imitations, ask for Aquatic Glassel by Moderustic. Be sure to get a price quote and you'll see the difference.
We are now designing a national catalog which should be 30 to 50 pages! We are asking for your help in acquiring pictures of fireplaces and fire pits for our catalog that our glass was used in. We would also appreciate your comments and or feed back as well. Please send your e mails and pictures to: Ed@Moderustic.com Jaunzemis@msn.com
Any questions please contact us at: Phone: 909 989 6129
Fax: 909 944 3811 E Mail: Ed@Moderustic.com
Stop by and visit our Showroom in Rancho Cucamonga: Moderustic Inc. 9467 Ninth Street #D Rancho Cucamonga, California 91730
CSLB# C-17 693887
We are 2 miles north of the Ontario Airport Hours: M-F 8:00 to 6:00 Every Saturday 10:00 to 2:00. After hours appointments available on request. If you're coming late, please call and we will wait. We usually stay until 6:00 pm.
We at Moderustic and Producers of Aquatic Glassel and the inventors of Fireplace Glass, are proud to offer the consumer over 500 products and we know we have spawned a few undesirable competitors in the market place but we continue on our quest for betterment and greater success through you the customer. We have been criticized for offering the crushed lava rock and or filler method by all of these other companies. But we understand the wants and needs of the customer, you. Spend less and get more. Some of these companies are telling the consumer to not use filler, why? They only want to fill their pockets with your money and we want you to save money. We know we have devastated these companies with our filler saving methods but it is with the best intentions for the consumer in mind. We have refused to sell to these individuals and companies because of their business practices. So please understand their intentions when they want you to purchase more glass. We take pride in our new product and take Patent Infringement very seriously! There are several companies who have copied our product and or process and they will be in for a surprise when our patent number becomes available to the public and they will find their business in ruin. If you are a previous or new customer and would like to add your comments on these companies or your experience, we will post a testimonial page for these to be read by the public. If you would like to post just your comments, they are welcome as well. Again, we work for the consumer and not the competition.
Moderustic Return Policy
Moderustic Inc Return Policy and Legal Notices • Returns must be made within 30 days of purchase with exceptions only by management. • Returned products must be unused and/ or unmixed. • Returned products must be packaged well to avoid damage in transit, OR YOU WILL BE RESPONSIBLE FOR THE DAMAGE. • Returned products that are damaged in transit will not be able to be refunded. • Refunds will be made towards product cost only. • Refunds will not be given for non-product labor costs (consulting fees, installation fees, labor, shipping etc.) • Restock fees may apply depending on which items are being returned. (10% to 70%) • Refunds are processed after customer’s review and acceptance of refunded amount. • Refunds take approximately 1 week for processing less any customer delays. • Any return must have a return authorization in writing by the management and this will be noted. • There are no returns or refunds on any custom metal products what so ever! • We are not responsible for local codes and or if any of our products are or are not approved. Please check with your local building department or governing agencies for proper approvals before purchasing. Custom built or designed items are not returnable for any reason. • Any Designs, Drawings, PDF Files, Ideas, Pictures, Attachments, Renderings, Facsimiles, Faxes, Blue Prints, Copies, Documents and even copy written materials once sent to Moderustic Inc, Ed Jaunzemis, Aquatic Glassel or any employee of Moderustic Inc becomes property of said company to use, distribute, copy, reproduce, manipulate, recreate, modify, advertise, promote, lay claim to and or use in our discretion as we need. If you do not agree with these terms then please do not send us anything. Our intentions are to create for you the "Customer" and it is our vast collection of material that will spawn an idea for you to have us create something for you. If we should create something/ anything for you that is one of a kind, you do not own any rights to this or there idea or ideas, product or concept in any way shape or form. • EXPEDITED SHIPPING NOTICE (i.e. 2/ 3-Day Select, Next Day/ 2nd Air, etc.): If UPS/ FedEx fails to deliver your packages within the expedited delivery time frame you have chosen, they can or will refund a PORTION of the delivery charges. We will pass 100% of the UPS/ FedEx refund back to you. The amount refunded is determined by UPS/ FedEx and will be less than the original expedited shipping charge that you originally paid. This is due to surcharges and fuel charges. We do not determine what will be credited back.
Moderustic Inc Ed Jaunzemis, President 9467 9th Street Suite D Rancho Cucamonga, California 91730 Phone 909 989-6129 Fax 909 944-3811
Can you honestly say logs look good?
